







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterHow Are Custom Windows Made? A Vacaville Look Inside the Factory and the Frame
Custom windows are made in five stages: frame milling or extrusion, sash assembly, insulated glass unit (IGU) fabrication, hardware integration, and quality-control sizing. The stage that matters most happens before any glass goes in. In Vacaville, where summers push 95°F and the expansive clay under Browns Valley and Alamo Creek shifts every wet season, a custom window’s frame-to-sash connection is engineered to hold its geometry through that movement. A standard unit sized to a measured opening has no allowance for it. If you’re weighing custom against off-the-shelf, call (888) 276-8078 and we’ll walk your opening before you order.
From the curb, a custom window and a standard window can look identical. What you’re paying for is the engineering inside that frame.

What Actually Happens Inside a Custom Window Factory?
Two frame types dominate the custom market, and they behave very differently in Vacaville’s climate. Fiberglass frames are pultruded: continuous glass strands are pulled through a heated die, which locks the fibers into a dense, stable profile. Vinyl frames are extruded: hot PVC is pushed through a die, and the material expands and contracts more with temperature swings. Under three summers of Vacaville heat, a pultruded fiberglass frame holds its dimensions more predictably, while vinyl needs more room to move. Andersen builds its custom fiberglass lines around that pultrusion process; Marvin machines and assembles its wood and fiberglass frames to tight tolerances before the sash ever meets them.
Here’s the sequence a custom unit actually goes through:
- Frame mill or extrusion. The profile is cut or pultruded to the rough opening minus a clearance allowance. Custom units are typically ordered with about 1/4-inch clearance per side to absorb seasonal wall movement.
- Sash assembly. The moving panel is built and squared to the frame so the seals meet evenly around the full perimeter.
- IGU fabrication. The glass sandwich is built and sealed (more on this below).
- Hardware integration. Locks, hinges, and operators are set to the manufacturing tolerances the frame was built to.
- QC sizing verification. The finished unit is measured against the order spec before it ships.
That clearance allowance in step one is the quiet reason a custom unit fits a Vacaville house that moves. A tract home in the older core or a 1990s Browns Valley subdivision can swing a door frame a quarter inch between fall and spring; a window ordered to a bare measurement has nowhere to give.
Why the Insulated Glass Unit Decides 80% of Your Energy Performance
The IGU – the sealed glass sandwich – is built at the factory and you never see the choices made inside it. Three decisions there drive most of the window’s efficiency, and they aren’t visible once the unit is installed:
- Spacer bar. Warm-edge spacers conduct less heat at the glass edge than older aluminum spacers, which keeps the perimeter from fogging and condensing.
- Gas fill. Argon is the standard fill and handles most Vacaville homes well. Krypton is denser and gets used in thinner profiles or tighter spaces where argon can’t fit.
- Low-E coating. Soft-coat low-e goes on after the glass is made and delivers stronger solar control; hard-coat is applied during the float process and is more durable but less efficient. For a west-facing window taking Vacaville’s afternoon sun, soft-coat earns its place.
These are factory decisions, not site decisions. That’s why we ask about orientation and sun exposure before the order goes in – a west wall taking Delta-breeze heat and a shaded north wall don’t want the same glass.

How Long Do Custom Andersen and Marvin Windows Take in Vacaville?
Four to eight weeks from order to delivery is typical for custom Andersen and Marvin units. That lead time is why an October installation means an August planning conversation. Order in September for a fall install and you’re gambling on a ship date; order in August and the sequencing stays calm.
The factory controls the glass and the frame. The house controls the rest. Custom window warranties from Andersen and Marvin are installation-sensitive: improper flashing at the rough opening or bad shimming can void the IGU seal warranty, which protects the sealed unit itself. Get the flashing and shimming wrong and the seal fails, and the manufacturer points at the install. That’s where we come in – Windows & Doors work is something we do as a certified installer, and our 730-Day Done Right Promise runs alongside the manufacturer warranty, not instead of it. We also keep a curated set of brand partners across the trades, from Andersen and Marvin on windows to ActiveYards on fencing, so the material line stays consistent from one project to the next.
If you’re comparing options for your opening, our Vacaville service area page covers what we handle locally, and you can always start with an overview of how we work.
What Should You Compare Before You Order Custom Windows?
Compare the frame material, the IGU spec, the clearance allowance, and the installer’s warranty in writing – in that order. The unit price only tells you half the story.
| Item | Typical Vacaville range |
|---|---|
| Window replacement (whole project) | $4,500-$15,000 |
| Impact window installation | $8,000-$25,000 |
| Custom Andersen or Marvin lead time | 4-8 weeks |
| Frame clearance allowance (per side) | ~1/4 inch |
A few questions worth asking any installer before you sign:
- What frame material are you specifying, and why for this wall?
- What’s the IGU spec – spacer type, gas fill, coating?
- How will you flash and shim the opening?
- What does your workmanship warranty cover, and for how long?
We answer those with upfront pricing, no surprises: the number you see is the number you pay. Financing runs 0% for 18 months, and projects over $10,000 get $1,000 off, so the custom route doesn’t have to be a cash-only decision.
FAQs
Custom windows are built to your specific opening with engineered frame clearance and a chosen IGU spec, while standard windows are built to fixed sizes with no allowance for a house that moves. In Vacaville, that clearance allowance is the difference between a window that operates smoothly for years and one that binds after a wet season of clay expansion.
A full window replacement project in Vacaville typically runs $4,500-$15,000, and impact window installation runs $8,000-$25,000. The final number depends on unit count, frame material, and glass spec. Call (888) 276-8078 for an exact quote – estimates are free.
Yes, if you plan the order by August. Custom Andersen and Marvin units take 4-8 weeks to arrive, so an October install means starting the conversation in late summer. Call (888) 276-8078 and we’ll map the timeline against your install window – estimates are free.
Manufacturer warranties on the glass unit are installation-sensitive and can be voided by improper flashing or shimming, so the install warranty matters as much as the factory one. Our 730-Day Done Right Promise covers workmanship for two full years and runs alongside the manufacturer coverage. Call (888) 276-8078 to talk through both.
If you’d rather have your openings looked at before you order, Groundwork Construction Co. of Vacaville offers a no-pressure assessment in Vacaville – call (888) 276-8078. Our technicians have up to 12 years of experience, and calls are answered by a live person 24/7.
Written by the team at Groundwork Construction Co. of Vacaville, serving Vacaville, CA.


