







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Brentwood, CA: What It Costs and How Long It Takes
A chain link fence in Brentwood, CA typically runs $3,500 – $9,000 for a standard residential yard, with most lots landing near the middle of that range. Figure roughly two to four days on site once the layout is marked, posts are set, and the gates are hung. That price and schedule hold on flat, formerly agricultural lots all over 94513. Call (888) 276-8078 to schedule a free on-site estimate.
How a Chain Link Fence Goes Up Here, Step by Step

Every chain link job follows the same order. The differences that matter in Brentwood come from what’s under the ground, not from the fence itself.
- 1
Site walk and layout (day 1, 1 – 2 hours). We mark corners and gate posts with string lines and a tape, confirm the property line against the plat or survey, and flag irrigation heads, septic components, and utility locates. You decide the gate swings, the post spacing, and whether the fence sits at the property line or a foot inside it.
- 2
Utility locate and line check (72 hours before digging). Free national locate request plus a walk of the route with a probe. On Brentwood’s former orchard land, this is where we find old irrigation mains and drain tile that never made it onto subdivision maps.
- 3
Post setting and concrete cure (day 1 – 2). Terminal, corner, and gate posts get deeper footings and more concrete than line posts; line posts generally go in a hole roughly 8 inches across and two feet deep in firm soil. Concrete needs 24 to 48 hours to set before tensioning, so the crew usually leaves the line standing overnight.
- 4
Framework, mesh, and gates (day 2 – 3). Top rail, tension wire or bottom rail, then mesh pulled under tension and cut on a slight jog to reduce a shoulder strap or holster from catching. Walk gates and drive gates get their hinges, latch, and drop rod, then swing to check clearance.
- 5
Final walk and clean-up (last day, 30 – 60 minutes). You walk the line with us, check every gate latch and tension, confirm no concrete splash on the stucco, and approve the finished run before we close it out.
You’re making decisions at three points: layout, gate hardware, and final tension. Everything in between is on us, and the whole run is covered by our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Options You’ll Choose Between
Chain link is a simple product with a few specs that actually change the price and how long it lasts in Brentwood’s sun and rain.
- Gauge of wire and mesh. The most common residential mesh is 11.5-gauge, at a cheaper per-foot cost. Move to 9-gauge for a heavier, harder-to-cut mesh that holds tension longer under a dog running the line and will cost noticeably more per foot. For anything bordering a road or a busy shared line, 9-gauge is the honest pick.
- Post and rail sizing. 1-5/8″ line posts are the residential standard; 2-3/8″ posts are sturdier for corner and gate posts or for a run over 6 feet tall and add to the cost. Wind load and gate weight drive this decision more than the fence height alone.
- Coating and color. Galvanized is the default and the most economical. Vinyl-coated black or green has a longer paint hold under intense Central Valley sun and runs higher. Within coated options, ask whether the coating is bonded or extruded; extruded holds up better against scratches.
- Top rail, bottom rail, or tension wire. Top rail is standard. Bottom rail adds structure and cost but helps on driveways and slopes; tension wire is a cheaper bottom option that keeps the mesh from curling up when animals push it.
- Gate hardware. Self-closing, self-latching hardware matters if the yard serves a pool or a dog. Drop rods and heavier hinges for a double drive gate cost more and are worth it.
- Height. Standard residential is 4 to 6 feet. Anything over 6 feet adds posts, concrete, and labor. Check HOA rules before you go taller.
What a Chain Link Fence Costs in Brentwood, CA

Plan on $3,500 – $9,000 for a chain link fence in Brentwood. A standard backyard run with 4-foot galvanized mesh and one walk gate usually lands near the low end. A full perimeter with 6-foot 9-gauge, black vinyl coating, a double drive gate, and a commercial-grade corner post will push toward the top.
Four things move the number:
- Linear feet. Straight line length with corners is the biggest single driver. Every gate counts as two terminal posts, and each of those gets a heavier footing.
- Terrain and tearing out the old line. A slope that needs stepped posts (each drop gets its own staging) costs more than a flat run. Removing concrete footings from an old fence, or breaking out a section of concrete or asphalt under the new line, adds labor.
- What’s under the surface. On former orchard land east and south of town, hitting an old irrigation line or unknown drain tile means hand digging, careful hand grubbing around the pipe, and sometimes trimming the post back from it. That’s real time and it doesn’t happen on newer infill lots.
- Height and gauge. Going from 4-foot to 6-foot adds concrete, post size, and labor. 9-gauge over 11.5-gauge adds material cost.
- Permit scope. A short residential run may not require a permit; a run over 6 feet, a fence near a pool, or anything bordering a public right-of-way usually does. We check with the City of Brentwood’s building department, pull what’s needed, and pass the inspection. If you’re tying the fence to a wider project, it’s part of a full Fence Installation in Brentwood scope.
A written estimate from us is line-item: linear feet, gauge, post size, gate count, concrete, tear-out, and permit fees. What’s not in it: old lawn or sprinkler lines you want moved, and any portion of the line that has to be rebuilt after a locator uncovers a surprise. Those are quoted before we touch them, never billed by surprise.
See the difference
Before
After
Before
After
Before
AfterWhat Brentwood’s Layout Means for Your Fence
Brentwood has spent the last two decades converting orchards and pasture into large master-planned subdivisions, and that frontier rhythm shapes this job more than anything else. New phases open alongside land still in active orchards and vineyards, so we’re often working right at that suburban-agricultural edge. On freshly graded former orchard land, crews regularly hit old irrigation lines, land-leveling grades, and unrecorded ag-era drain tile that never made it onto subdivision maps. That’s a common surprise along Marsh Creek Road and out toward the rural parcels east of town that Antioch’s older infill lots almost never produce. The dominant housing here is late-1990s-to-2020s stucco-and-tile construction, so most fence work sits on newer lots where the line is level and the challenge is underground rather than aging posts. There’s still a small older core near downtown along First and Second Streets where the fences are original and the footings are set in older concrete. HOA rules in the planned communities here often specify fence height, color, and material, so we check those before the layout is final. Inland East Contra Costa’s hot, dry summers also matter: mesh pulled too tight in July will go slightly slack by the next cool morning, and a vinyl coating takes a beating under that sun, so we set tension with the season in mind. The winter wet season can also surface drainage problems on the new former-farmland lots where grading wasn’t finished, which is worth catching during the site walk.
Serving Brentwood, CA – Our Local Coverage Area
We serve Brentwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Chain Link Fence in Brentwood

Most residential chain link fence jobs in Brentwood take two to four days on site, with the concrete footings needing 24 to 48 hours to cure before the mesh is tensioned. A short backyard run can finish in two days; a full perimeter with a double drive gate usually pushes to four. Call (888) 276-8078 to get a firm schedule on your lot.
Short residential chain link fence runs often don’t need a permit in Brentwood, but anything over 6 feet tall, near a pool, or along a public right-of-way generally does. We check with the City of Brentwood’s building department before the layout is final and pull what’s required. Call (888) 276-8078 and we’ll confirm for your specific address.
Between $3,500 and $9,000 for a standard residential yard in Brentwood. The low end is a 4-foot galvanized backyard run with one gate; the high end is a full 6-foot 9-gauge vinyl-coated perimeter with a double drive gate on a sloped lot. Call (888) 276-8078 for an exact quote; estimates are free and line-item.
Yes, in most cases. We do a utility locate and walk of the line beforehand and hand-dig around anything we find, including old irrigation lines and drain tile common on former orchard land in Brentwood. If a post location has to shift to avoid a buried line, we tell you before digging. Homeowners often pair this with ADU Site Prep & Utilities in Brentwood when they’re reworking the property’s underground layout.
Every chain link fence we install is covered by our 730-Day Done Right Promise. If a footing settles, a gate sags, or the mesh goes slack within that window, we come back and make it right. Call (888) 276-8078 to read the terms in full.
Get a Free Chain Link Fence Estimate in Brentwood
We’ll walk your property in Brentwood, check the line against the plat, probe for anything under the surface, and hand you a written, line-item estimate for your chain link fence. No pressure and no surprises. If the fence is part of a bigger job, we’ll fold it into our Fence Installation scope or pair it with Door Installation in Brentwood on a shared visit. We cover all of Brentwood and the surrounding area, including Oakley, Discovery Bay, Antioch, and Clayton. Call (888) 276-8078 to book yours.
Written by the team at Groundwork Construction Co.












